INSTALLATION INSTRUCTIONS FOR PART 95-3304
APPLICATIONS
See application list inside
GM multi-kit 2005-up
95-3304
KIT FEATURES
• Double DIN radio provision
• Stacked ISO DIN head unit provision
KIT COMPONENTS
• A) Trim Plate • B) Brackets
A
B
WIRING & ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• GMOS-01 GM Onstar and chime harness 2002-up
• GMOS-04 GM Onstar and chime and amp harness 2002-up
Antenna Adapter:
• 40-GM10 GM antenna adpter 1988-up
TOOLS REQUIRED
Socket Wrench • Phillips Screwdriver • Small Flat Blade Screwdriver
METRA. THE WORLD’S BEST KITS.™
metraonline.com
1-800-221-0932
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
Dash Disassembly 95-3304
Buick Terraza 2005-2008
Chevrolet Uplander 2005-2008
Pontiac Montana SV6 2005-2007
Saturn Relay 2005-2007
1. Unclip and remove trim panel around
radio and a/c control. (Figure A)
2. Remove (8) 9/32” screws to extract
radio and a/c control from sub dash.
(Figure A)
Continue to kit assembly
(Figure A)
3
Dash Disassembly 95-3304
Chevrolet Corvette 2005-up
1. Unclip and remove ride control switch/
3. Unclip and remove entire panel
surrounding radio and including
a/c controls. (Figure A)
blank plate at front edge of center
console lid. (Figure A)
2. Remove (2) 9/32” screws from under
4. Remove (4) 9/32” screws securing radio
plate removed in step 2. (Figure A)
to extract from sub dash. (Figure A)
Continue to kit assembly
(Figure A)
4
Dash Disassembly 95-3304
Hummer H3 2006-2010
1. Unclip and remove trim panel around
radio and a/c controls. (Figure A)
2. Remove (4) 9/32” screws securing
radio. (Figure B)
3. Unplug and remove radio.
Continue to kit assembly
(Figure A)
(Figure B)
5
Kit Assembly 95-7951
Double DIN radio provision
1. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2. Slide the appropriate bracket into the
trim plate aligning the holes in the trim
plate to the clips on the bracket.
(Figure A)
3. Slide the DDIN radio unit into the trim
plate bracket assembly and secure the
unit to the kit using the screws supplied
with the head unit. (Figure B)
(Figure A)
4. Reassemble dash in reverse order
of disassembly.
(Figure B)
6
Kit Assembly 95-7951
Stacked ISO DIN head unit provision
1. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2. Slide the appropriate bracket into the
trim plate aligning the holes in the trim
plate to the clips on the bracket.
(Figure A)
3. Slide the stacked ISO DIN units into the
(Figure A)
trim plate bracket assembly and secure
the unit to the kit using the screws
supplied with the head unit. (Figure B)
4. Reassemble dash in reverse order
of disassembly.
(Figure B)
7
INSTALLATION INSTRUCTIONS FOR PART 95-3304
METRA. THE WORLD’S BEST KITS.™
metraonline.com
1-800-221-0932
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
|